Subcommittee | Subcommittee Title | Published standards | Standards under development |
---|---|---|---|
ISO/TC 17/SC 1 | Methods of determination of chemical composition | 61 | 8 |
ISO/TC 17/SC 3 | Steels for structural purposes | 25 | 2 |
ISO/TC 17/SC 4 | Heat treatable and alloy steels | 30 | 1 |
ISO/TC 17/SC 7 | Methods of testing (other than mechanical tests and chemical analysis) | 16 | 6 |
ISO/TC 17/SC 9 | Tinplate and blackplate | 3 | 3 |
ISO/TC 17/SC 10 | Steel for pressure purposes | 17 | 9 |
ISO/TC 17/SC 11 | Steel castings | 21 | 3 |
ISO/TC 17/SC 12 | Continuous mill flat rolled products | 32 | 4 |
ISO/TC 17/SC 15 | Railway rails, rails fasteners, wheels and wheelsets | 15 | 0 |
ISO/TC 17/SC 16 | Steels for the reinforcement and prestressing of concrete | 25 | 6 |
ISO/TC 17/SC 17 | Steel wire rod and wire products | 23 | 5 |
ISO/TC 17/SC 19 | Technical delivery conditions for steel tubes for pressure purposes | 35 | 0 |
ISO/TC 17/SC 20 | General technical delivery conditions, inspection documents and sampling for mechanical testing | 7 | 1 |
ISO/TC 17/SC 21 | Environment related to climate change in the iron and steel industry | 5 | 2 |
Filter :
Standard and/or project under the direct responsibility of ISO/TC 17 Secretariat | Stage | ICS |
---|---|---|
Title missing
|
95.99 | |
Selection and preparation of samples and test pieces of wrought steels — Part 2: Samples for the determination of the chemical composition
|
95.99 | |
Dimensions of hot-rolled steel sections — Part 1: Equal-leg angles — Metric series — Dimensions and sectional properties
|
95.99 | |
Dimensions of hot-rolled steel sections — Part 2: Unequal-leg angles — Metric series — Dimensions and sectional properties
|
95.99 | |
Dimensions of hot-rolled steel sections — Part 3: Equal-leg angles — Inch series — Dimensions and sectional properties
|
95.99 | |
Dimensions of hot-rolled steel sections — Part 4: Unequal-leg angles — Inch series — Dimensions and sectional properties
|
95.99 | |
Dimensions of hot-rolled steel sections — Part 7: Parallel flange I-beams — Inch series — Dimensions and sectional properties
|
95.99 | |
Dimensions of hot-rolled steel sections — Part 9: Parallel flange column sections — Inch series — Dimensions and sectional properties
|
95.99 | |
Hot-rolled steel sections — Part 13: Tolerances on sloping flange beam, column and channel sections
|
95.99 | |
Railway rolling stock material — Part 1: Rough-rolled tyres for tractive and trailing stock — Quality requirements
|
95.99 | |
Railway rolling stock material — Part 2: Rough tyres for trailer stock — Dimensions and tolerances
|
95.99 | |
Railway rolling stock material — Part 4: Rolled or forged wheel centres for tyred wheels for trailer stock
|
95.99 | |
Railway rolling stock material — Part 5: Cast wheel centres in non-alloy steel for tyred wheels for trailer stock
|
95.99 | |
Railway rolling stock material — Part 6: Solid wheels for tractive and trailing stock — Quality requirements
|
95.99 | |
Single cold-reduced tinplate and single cold-reduced blackplate — Part 1: Electrolytic and hot-dipped tinplate sheet and blackplate sheet
|
95.99 | |
Single cold-reduced tinplate and single cold-reduced blackplate — Part 2: Electrolytic tinplate coil and blackplate coil for subsequent cutting into sheet form
|
95.99 | |
Steel — Conversion of elongation values — Part 1: Carbon and low alloy steels
|
95.99 | |
Steel products for pressure purposes — Derivation and verification of elevated temperature properties — Part 1: Yield or proof stress of carbon and low alloy steel products
|
95.99 | |
Steel products for pressure purposes — Derivation and verification of elevated temperature properties — Part 2: Proof stress of austenitic steel products
|
95.99 | |
Steels and cast iron — Determination of phosphorus — Spectrophotometric method
|
95.99 | |
Tinplate and blackplate — Minimum packaging requirements
|
95.99 | |
Ferrous products — Heat treatments — Vocabulary
|
95.99 | |
Ferrous materials — Heat treatments — Vocabulary
|
95.99 | |
Ferrous materials — Heat treatments — Vocabulary
|
90.92 | |
Ferrous materials — Heat treatments — Vocabulary
|
20.00 |
|
Steels — Classification — Part 1: Classification of steels into unalloyed and alloy steels based on chemical composition
|
90.93 | |
Steels — Classification — Part 2: Classification of unalloyed and alloy steels according to main quality classes and main property or application characteristics
|
90.93 | |
Steel names based on letter symbols
|
95.99 | |
Steel names based on letter symbols
|
95.99 | |
Steel names based on letter symbols
|
90.93 | |
Double cold-reduced electrolytic tinplate — Part 1: Sheet
|
95.99 | |
Double cold-reduced electrolytic tinplate — Part 2: Coil for subsequent cutting into sheets
|
95.99 | |
Railway rolling stock material — Ultrasonic acceptance testing
|
95.99 | |
Steel products — Definitions and classification
|
95.99 | |
Steel products — Vocabulary
|
90.93 | |
Basic rules for specifying impact strength in steel specifications
|
95.99 | |
Single cold-reduced electrolytic chromium/ chromium oxide-coated steel — Part 1: Sheets
|
95.99 | |
Double cold-reduced electrolytic chromium/ chromium oxide-coated steel — Part 1: Sheets
|
95.99 | |
Guideline for Smart Manufacturing in Iron and Steel Industry
|
20.60 |
|
No matching records found. Please try changing the filter settings.